05MR103 城市道路--立体交叉可行性研究、初步设计深度图样

作者:标准资料网 时间:2024-05-19 09:44:38   浏览:8186   来源:标准资料网
下载地址: 点击此处下载
基本信息
标准名称:城市道路--立体交叉可行性研究、初步设计深度图样
发布日期:
实施日期:2005-06-01
首发日期:
作废日期:
起草单位:上海市政工程设计研究院
出版社:中国建筑标准设计研究院
出版日期:2005-06-01
页数:8开,61页
适用范围

城市道路立体交叉工程设计城市道路专业推荐的可行性研究、初步设计绘图示例。

前言

没有内容

目录

目录 1 编制说明 3 城市立交设计概述 4 城市立交可行性研究设计图纸(总体设计及线形设计) 图纸目录 8 工程地理位置图 9 工程效果图 10 预测交通流量流向图 11 总体设计图 12 平面设计图(一)~(五) 13 汶水路高架道路纵断面设计图(一)~(三) 18 WS匝道纵断面设计图 21 WN匝道纵断面设计图 22 典型横断面设计图 23 规划横断面图 24 快速系统交通组织设计图(一)~(五) 25 辅道系统交通组织设计图(一)~(五) 30 立交附近路网交通组织图 35 城市立交初步设计图纸(总体设计及线形设计) 图纸目录 36 工程地理位置图 37 工程效果图 38 预测交通流量流向图 39 总体设计图 40 平面线位设计图(一)~(三) 41 高架道路平面设计图(一)~(四) 44 地面道路平面设计图(一)~(四) 48 莘县路高架道路纵断面设计图(一)~(三) 52 莘县路地面道路纵断面设计图(一)~(三) 55 A匝道纵断面设计图 58 B匝道纵断面设计图 59 典型横断面设计图 60 立交附近路网交通组织图(一)~(二) 61

引用标准

没有内容

所属分类: 化工 橡胶制品及其辅助材料 其他橡胶制品 橡胶和塑料工业 橡胶和塑料制品 其他橡胶和塑料制品
下载地址: 点击此处下载
【英文标准名称】:Methodsoftestforproductioncontrolofconcrete--Methodoftestforsurfacemoistureinfineaggregatebycentrifugalforce
【原文标准名称】:混凝土生产控制的试验方法.用离心力对细集料表面含水率的试验方法
【标准号】:JISA1802-2009
【标准状态】:现行
【国别】:日本
【发布日期】:2009-03-20
【实施或试行日期】:2009-03-23
【发布单位】:日本工业标准调查会(JP-JISC)
【起草单位】:TechnicalCommitteeonCivilEngineering
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:ThisJapaneseIndustrialStandardspecifiesmethodsoftestforsurfacemoistureinfineaggregatebycentrifugalforcetobeappliedmainlytoproductioncontrolofcon-crete.ThisStandardisapplicabletocrushedsand,fineslagaggregateandsand.Further,thesurfacemoistureobtainedsurfacemoisture.accordingtothistestiscalledascentrifugal
【中国标准分类号】:Q13
【国际标准分类号】:91_100_30
【页数】:9P.;A4
【正文语种】:日语


Product Code:SAE AMS5863
Title:Steel, Corrosion Resistant, Sheet, Strip, and Plate, 15Cr - 6.5Ni - 0.75Mo - 0.60Cb - 1.5Cu, Solution Heat Treated, Precipitation Hardenable
Issuing Committee:Ams F Corrosion Heat Resistant Alloys Committee
Scope:This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.These products have been used typically for parts requiring corrosion resistance and high strength in service up to 700 °F (371 °C), but usage is not limited to such application. Product can be used in the solution heat treated condition and is capable of being precipitation heat treated to tensile strengths as high as 180 ksi (1241 MPa).Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after precipitation heat treatment; ARP1110 recommends practices to minimize such conditions.